365体育开户

Hello, welcome to the official website of Dongguan Jiabang Machinery Equipment Co., Ltd.!
Favorite Jiabang | Online Message | Contact Us
Main industrial oven, tunnel oven, double-pull assembly line ...
National Consulting Hotline: 13712718109
Jiabang Product Center
4Products
Your location: Home- > Products
加热固化小型工业烤箱
Heat curing small industrial oven <br> Special offer small industrial oven productsHeat curing small oven energy saving low noise small oven Jiabang machinery non-standard custom

Heat curing small industrial oven

Details


This equipment is suitable for a variety of products or materials and electrical, instruments, meters, components, electronics, electrical and automotive, aviation, communications, plastics, machinery, chemicals, food, hardware tools for drying and constant temperature under constant temperature environment Adaptability test.

Oven use:

1. The oven should be placed in a dry and horizontal place in the room to prevent vibration and corrosion.

2. Pay attention to the safe use of electricity, and install a sufficient capacity switch blade according to the power consumption of the oven. Use enough power wires and have a good ground wire

3. An oven with an electric contact mercury thermometer type thermostat should connect the two wires of the electric contact thermometer to the two terminals on the top of the box respectively. Another ordinary mercury thermometer is inserted into the exhaust valve. (The thermometer in the exhaust valve is used to calibrate the electrical contact mercury thermometer and the actual temperature in the observation box.) Open the hole of the exhaust valve. Adjust the mercury thermometer at the electrical contact to the required temperature and tighten the screws on the steel cap to achieve the purpose of constant temperature. However, care must be taken not to rotate the indicator iron beyond the scale when adjusting.



4. When everything is ready, put the sample in the oven, and then connect and turn on the power. The red indicator light is on to indicate that the oven is heated. When the temperature reaches the controlled temperature, the red light turns off and the green light turns on, and the constant temperature starts. To prevent temperature control failures, care must also be taken.

5. Care should be taken not to place the samples too densely when placing them in the sample. No test article should be placed on the heat sink to avoid affecting the upward flow of hot air. Baking of flammable, explosive, volatile and corrosive items is prohibited.

6. When you need to observe the samples in the working room, you can open the outer box door and observe through the glass door. However, it is better to open the door as few as possible, so as not to affect the constant temperature. Especially when working above 200 ° C, opening the door of the box may cause the glass door to suddenly cool and break.

7. The blower oven, the blower must be turned on during the heating and constant temperature process, otherwise it will affect the uniformity of the temperature of the working room and damage the heating element. 8. After work is completed, the power shall be cut off in time to ensure safety.

8. Keep the inside and outside of the oven clean.

9. When using, do not exceed the temperature of the oven

10. In order to prevent burns, special tools should be used when taking and placing the test specimen.








Precautions and maintenance of drying equipment such as ovens

1. Pay attention to the correct voltage before use. Only the voltage marked on the machine is used to avoid excessive electricity and fire.

2. Do not place in a humid place to prevent leakage.

3. When the temperature changes during use, do not open the machine at will.

4. When the difference between the displayed temperature and the actual temperature is large, it is not allowed to adjust the components of the circuit board at will, and the manufacturer should be notified to dispatch it.

5. Do not rinse directly with water to prevent leakage.

6. It is forbidden to put flammable and explosive substances such as alcohol and acidic items with volatile items in the machine to prevent accidents.

7. Do not use flammable materials near the instrument to prevent accidents.

8. Please be careful to put items in the studio, not easy to overfill.

HomeAbout JiabangProductsCompany RealityPartnersQualification CertificateNews CenterIndustry NewsOnline MessageContact Us
copyright 技术支持: 东莞网站建设访问量: Dongguan Jiabang Machinery Equipment Co., Ltd. Copyright © copyright Technical Support: Dongguan Website Construction Visits:
Contact: Mr. Lu / 13712718109 Address: No.302 Heluling, Huanzhuli Village, Changping Town, Dongguan, Guangdong Province [ Bmap ] [ Gmap ] [ Background Management ] [ Baidu Statistics ]
* The relevant webpage materials and related resources on this site are from the Internet. If there is any infringement, please inform us quickly. We will delete it within 24 hours. * Record No .: Guangdong ICP No. 17030238-1
Popular searches: Dongguan industrial ovens, tunnel furnace manufacturers, UV curing furnaces, oil spray water cabinets
  • Back to top
  • Download Mobile APP
    Download Mobile APP