Jiabang thank you for coming
+ 线上销售为一体的运营模式，专业生产设计各种电热工业烤箱、高温烤箱、 IR 隧道炉、 PCV 生产线、 Uv 固化炉、喷油水濂柜、自动加油线、整套涂装设备等都可按客户的需要来定制， 如需定制 请 您与 我们联系 13712718109 吕先生 , 确认相关产品精 量及款式型号等，真诚期待与您合作，谢谢！ Our company is based on the operation mode of factory production + online sales, specializing in the production and design of various electric industrial ovens, high temperature ovens, IR tunnel furnaces, PCV production lines, Uv curing furnaces, fuel injection cabinets, automatic fueling lines, complete sets Painting equipment can be customized according to customer's needs. If you need customization , please contact us 13712718109 Mr. Lu to confirm the precision and style of related products . We sincerely look forward to working with you, thank you!
The inner liner is made of 1.2 thick 304 # stainless steel plate. The bottom plate is made of 2.0mm thick stainless steel plate and multiple stainless steel angle irons as stiffeners. It bears 200KG weight and does not rust, which makes the furnace clean and dust free. Inner tank clearance size: 1.0m wide, 1.5m high, 1.1m deep, 100mm thick high temperature silicic acid rock wool is placed around the inner liner, and high temperature resistant sealed silicone strips are added around the door.
U 型发热管 于炉腔左侧，炉腔顶部配 0.75KW 运风马达一台 、配12寸运风风轮于炉腔顶部， 水平循环大风量强制运风方式 ，配进气、排气口阀门，排气阀门上加装高温风机进行抽气.可调节空气流量，使炉内温度更加均匀。 Built-in stainless steel heat sink U -shaped heating tube made in Taiwan is on the left side of the furnace cavity. The top of the furnace cavity is equipped with a 0.75KW wind motor and a 12-inch wind turbine is installed on the top of the furnace cavity . Inlet and exhaust valve, high temperature fan is installed on the exhaust valve to extract air. The air flow can be adjusted to make the temperature in the furnace more uniform.
台湾台松微电脑智能型 LED 数显温控器 ，采用模块连续缓冲式输出控制加热器, 采用 SSR 固态继电器输出加热器 ( 当温度到达设定温度值时 , 此时烤箱处于恒温状态 , 自动调整输出功率 , 从而降低整个烤箱的功率 , 达到省电效果 ) 颠覆传统过零触发时带来的电流瞬间冲击大、控温波动大等影响，配合性价比极高的DC24V输出型温控器，可使输出电压平稳线性变化，控温效果更稳定，性能更卓越，(可根据温度的误差大小自动调整输出功率的大小)使温度更加精准, 温度室温至 250 ℃任意可调 ，功能有 PID 自整定、自动恒温、自动计时 (配有高精度数显自动计时器可调99小时99分钟) 设有手动和自动计时开关选择 ,温度到后 定时报警断电、超温断电、漏电保护断路器、电机过载保护 等功能，定时和超温报警器及信号 Power 380V, three-phase five-wire system, power 30KW, equipped with control box on the right side of the oven, using Taiwan Taisong microcomputer intelligent LED digital temperature controller , using module continuous buffer output control heater, using SSR solid state relay Output heater ( when the temperature reaches the set temperature value , the oven is at a constant temperature at this time , the output power is automatically adjusted , thereby reducing the power of the entire oven and achieving power saving effects ) Subverting the traditional zero-cross trigger triggering a large instantaneous impact Large temperature fluctuations and other effects, combined with the extremely cost-effective DC24V output type temperature controller, can make the output voltage change smoothly and linearly, the temperature control effect is more stable, and the performance is more excellent, (the output power can be automatically adjusted according to the temperature error Size) makes the temperature more accurate. The temperature can be adjusted from room temperature to 250 ℃ . The functions include PID self-tuning, automatic constant temperature, and automatic timing. selection switch, the temperature after the alarm off, over-temperature power, earth leakage circuit breaker, motor overload protection and other functions, timing, and over-temperature alarm signal and Lights are individually controlled, and a display, dual thermostat control, the unique design of the over-temperature, over-temperature limit is provided with temperature control points to prevent damage to the main thermostat runaway its product, the temperature is more precise, load Internal temperature difference ± 2% degrees. The control box is equipped with a multi-color working indicator, which can display the working condition and faults of the oven.
Use of the oven:
1. The oven should be placed in a dry and horizontal place in the room to prevent vibration and corrosion.
2. Pay attention to the safe use of electricity, and install a sufficient capacity switch blade according to the power consumption of the oven. Use enough power wires and have a good ground wire
3. An oven with an electric contact mercury thermometer type thermostat should connect the two wires of the electric contact thermometer to the two terminals on the top of the box respectively. Another ordinary mercury thermometer is inserted into the exhaust valve (the thermometer in the exhaust valve is used to calibrate the electrical contact mercury thermometer and the actual temperature in the observation box) to open the hole of the exhaust valve. Adjust the mercury thermometer at the electrical contact to the required temperature and tighten the screws on the steel cap to achieve the purpose of constant temperature. However, care must be taken not to turn the indicator iron outside the scale during adjustment.
4. When all preparations are ready, put the sample in the oven, and then connect and turn on the power. The red indicator light indicates that the oven has been heated. When the temperature reaches the controlled temperature, the red light turns off and the green light turns on, and the constant temperature starts. In order to prevent temperature control from malfunctioning, care must be taken.
5. Care should be taken not to place the samples too densely when placing them in the sample. No test article should be placed on the heat sink to avoid affecting the upward flow of hot air. Baking of flammable, explosive, volatile and corrosive items is prohibited.
6. When you need to observe the samples in the working room, you can open the outer box door and observe through the glass door. However, it is better to open the door as few as possible, so as not to affect the constant temperature. Especially when working above 200 ° C, opening the door of the box may cause the glass door to suddenly cool and break.
7. The blower oven, the blower must be turned on during the heating and constant temperature process, otherwise the uniformity of the temperature of the working room and the heating elements will be damaged.
8. After work is completed, the power should be cut off in time to ensure safety.
9. Keep the inside and outside of the oven clean.
10. During use, the temperature should not exceed the operating temperature of the oven.
11. In order to prevent burns, special tools should be used when taking and placing the test specimen.