Most of the hot air circulates in the box, which has high thermal efficiency and saves energy. With the use of forced ventilation, the box is equipped with an adjustable air distribution plate, which dries the material evenly. The heat source can be steam, hot water, electricity, and far infrared. The machine has low noise and balanced operation. Temperature self-control, convenient installation and maintenance. It has a wide range of applications and can dry all kinds of materials. It is a universal drying equipment.
电动台车烘箱 1. Equipment name: Electric trolley oven
JXC-11066 2. Specifications: JXC-11066
2*1100W/380V 3. Blasting power: 2 * 1100W / 380V
室温+10~220度 4. Working temperature range: room temperature + 10 ~ 220 degrees
380V/N+1+地/50HZ 5. Operating voltage: 380V / N + 1 + ground / 50HZ
±1℃ 6. Temperature control accuracy: ± 1 ℃
27KW/分1档位控制 7. Heating power: 27KW / minute 1 gear control
±3℃（空载测试） 8. Temperature uniformity: ± 3 ℃ (no-load test)
根据客户产品需要 9, internal configuration: according to customer product needs
电感器线圈，電子 10. Adapt to the industry: inductor coil, electronics
1400*1900*2150 深*宽*高（mm） 11. Studio size: 1400 * 1900 * 2150 depth * width * height (mm)
1700*2550*2900(以实物为准)深*宽*高（mm） 12. Dimensions: 1700 * 2550 * 2900 (subject to the actual product) depth * width * height (mm)
本产品采用两侧出风，顶部回风循环，加热元件安装在箱体两侧风道内，循环电机 安装箱体顶部风道内， 可以让电机寿命延长，双开门 ,门扣采用羊角拉手固定。 13. Machine structure overview: This product uses two sides of the air, the top returns air circulation, heating elements are installed in the air ducts on both sides of the box, and the circulation motor is installed in the air ducts on the top of the box. The buckle is fastened with shorn handles.
1.2mm DC01碳钢冷轧板 板金折弯焊接铆钉拼接 14. Outer wall material of the box: 1.2mm DC01 carbon steel cold-rolled sheet
1.2mm SUS304不锈钢板 板金折弯机床冲孔 15. Box wind plate material: 1.2mm SUS304 stainless steel plate, sheet metal bending machine punching
1.0mm SUS304不锈钢板 板金折弯焊接铆钉拼接 16. Box air duct material: 1.0mm SUS304 stainless steel plate
强压循环运风 17. Air supply mode: strong pressure circulation wind
耐高温发泡硅橡胶条压迫式密封（如使用温度超过250℃，则采用硅酸铝纤维绳） 18. Door frame sealing material: high temperature resistant foamed silicone rubber strip pressure seal (if the use temperature exceeds 250 ℃, use aluminum silicate fiber rope)
LED液晶屏智能数显温控仪,控温精度±1℃，带PID调节，自动控温恒温 19, temperature control instrument: LED LCD screen intelligent digital display temperature control instrument, temperature control accuracy ± 1 ℃, with PID adjustment, automatic temperature control constant temperature
If the item you are baking contains volatile gas or corrosive objects, please explain in detail with our technical service personnel, if necessary, install explosion-proof devices or use explosion-proof electrical appliances. It is strictly forbidden to bake flammable and explosive materials directly! !! !!
Can be designed and customized according to customer product needs !!!!!
Use of the oven:
1. The oven should be placed in a dry and horizontal place in the room to prevent vibration and corrosion;
2. Pay attention to the safe use of electricity, and install a sufficient capacity power switch blade according to the power consumption of the oven. Use enough power wires and have a good ground wire;
3. An oven with an electric contact mercury thermometer type thermostat should connect the two wires of the electric contact thermometer to the two terminals on the top of the box. Another ordinary mercury thermometer is inserted into the exhaust valve (the thermometer in the exhaust valve is used to calibrate the electrical contact mercury thermometer and the actual temperature in the observation box) to open the hole of the exhaust valve. Adjust the mercury thermometer at the electrical contact to the required temperature and tighten the screws on the steel cap to achieve the purpose of constant temperature. But you must pay attention not to rotate the indicator iron outside the scale when adjusting;
4. When all preparations are ready, put the sample in the oven, then connect and turn on the power. The red indicator light indicates that the box has been heated. When the temperature reaches the controlled temperature, the red light turns off and the green light turns on, and the constant temperature starts. In order to prevent temperature control failure, you must also take care;
5. When placing the samples, pay attention not to arrange them too densely. No test article should be placed on the heat sink to avoid affecting the upward flow of hot air. Baking of flammable, explosive, volatile and corrosive items is prohibited;
6. When you need to observe the samples in the working room, you can open the outer box door and observe through the glass door. However, it is better to open the door as few as possible, so as not to affect the constant temperature. Especially when working above 200 ° C, opening the door of the box may cause the glass door to suddenly cool and crack;
7. The blower oven must be turned on during heating and constant temperature, otherwise it will affect the uniformity of the temperature of the working room and damage the heating element. 8. After work is completed, the power should be cut off in time to ensure safety;
8. Keep the inside and outside of the oven clean;
9. During use, the temperature should not exceed the operating temperature of the oven;
10. In order to prevent burns, special tools should be used when taking and placing the test samples.