Solid state relay program constant temperature and humidity test box
<br> Solid state relay program constant temperature and humidity test box Dongguan constant temperature equipment Jiabang manufacturers non-standard custom
Oven safe operating procedures
． 1 . Clean the surface and inner cavity for dust and keep the machine clean and hygienic.
2. Check whether the current of the ammeter is the same as normal. If there is something abnormal, notify the maintenance worker for maintenance.
3． Sudden power failure, turn off the heating switch to prevent it from starting automatically when a call comes in.
4． Check whether the fan is running normally and there are no abnormal sounds. If there is any, turn off the machine immediately and notify the maintenance worker for maintenance.
． 1 . Check that the air vents are not blocked and clean up the accumulated dust.
2. Whether the fan is operating normally.
3． The maintenance worker checks whether the current is normal.
4． Check whether the temperature controller is accurate. If not, please adjust the static compensation or sensor correction value of the temperature controller.
5. Check whether the heating tube is damaged and whether the wiring is aging.
6. Check whether the delayer is accurate and whether the error is allowed.
The indicator of the temperature controller: The green light is the electric heater is working, the red light is the heating stop, when the temperature in the box reaches the set temperature, the green light turns to the red light, after which the temperature controller continuously flips, the red and green lights alternately turn off, that Constant temperature,
2. Precautions for use
设备应指定专人操作,并定期保养,建立保养维修卡,非专业维修人员禁止拆卸或调整本设备内部电器参数 1.The equipment should be designated by a person to operate and regularly maintained, and a maintenance card should be established. Non-professional maintenance personnel are prohibited from disassembling or adjusting the internal electrical parameters of the equipment.
设备摆放区域严禁摆放易燃易爆物品,并设有有效的消防设施 2. It is strictly forbidden to place flammable and explosive items in the equipment placement area, and effective fire protection facilities are provided.
设备应放于平整,牢固的地面上,摆放区域应通风良好,并设有专用排风通道 3.The equipment should be placed on a flat, firm ground, the area should be well ventilated, and a dedicated exhaust channel should be provided.
设备配制电源线时,应适合设备功率,并在设备2米内配制断路器 4. When preparing the power cord for the equipment, it should be suitable for the power of the equipment, and a circuit breaker should be prepared within 2 meters of the equipment.
自设备内取出产品时,应采取有效防护措施,防止烫伤 5. When taking the product out of the equipment, effective protection measures should be taken to prevent burns
温控仪表上A/M键所对应的指示灯MAN严禁按亮，是自动切换到手动的按键，MAN指示灯按亮后温度将直线上升，不受所设定的温度限制。 6. The indicator light corresponding to the A / M key on the temperature control instrument is strictly forbidden to turn on. It is a button that automatically switches to manual. After the MAN indicator light is turned on, the temperature will rise linearly, regardless of the set temperature limit.
烤箱属常温烤箱:严禁烘烤,易燃易爆物品 7. Oven is room temperature oven: baking is strictly prohibited, flammable and explosive items
此烤箱安全正确接地线. 8. This oven is properly grounded.
发现烤箱内无风吹出,应改变电源相序 9. It is found that there is no wind blowing out of the oven, the power phase sequence should be changed
如需计时烘烤时间，首先应调整好所需烘烤时间，再打开计时开关，不应打开计时开关后再作时间调整，这样会导致计时错误。 10. If you need to measure the baking time, you should first adjust the required baking time, and then turn on the timing switch. You should not turn on the timing switch and then adjust the time. This will cause timing errors. Avoid high temperatures when removing the product! !! !!
严禁任意修改温控器和计时器的内部参数，温控器的输出OUTL参数不能为0。 11. It is strictly forbidden to modify the internal parameters of the thermostat and timer arbitrarily. The OUTL parameter of the thermostat cannot be 0.
、 操作人员必需严格执行操作规程，不得为赶工时违反操作。 12. The operator must strictly implement the operating procedures, and must not violate the operation when he is in a hurry.
Related Product Guidelines